REFLECTOR:Foil Tape Antennas

Donald Royer reflector@tvbf.org
Sun, 4 May 2003 14:40:59 -0600


This is a multi-part message in MIME format.

------=_NextPart_000_000C_01C3124B.2DAD86E0
Content-Type: text/plain;
	charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable

I think that we are having some nomenclature problems here. Of course =
the localizer uses the same antenna at the VOR. The localizer =
frequencies are simply the bottom end of the nav frequency band. The =
glide slope receiver can also be split off of the nav antenna but it is =
probably better to have a separate antenna. If a separate glide slope =
antenna is used it is a short one which is usually mounted between the =
bottom of the windshield  and the canard doghouse. The long antenna that =
is usually mounted on the cabin floor is the marker beacon antenna.
  ----- Original Message -----=20
  From: Tom Martino=20
  To: reflector@tvbf.org=20
  Sent: Sunday, May 04, 2003 1:03 PM
  Subject: RE: REFLECTOR:Foil Tape Antennas


  I was told you could use the VOR antenna for the localizer and you =
didn't need a separate antenna.

  =20

  =20

  -----Original Message-----
  From: Andy Millin [mailto:amillin@net-link.net]=20
  Sent: Sunday, May 04, 2003 7:45 AM
  To: reflector@tvbf.org
  Subject: RE: REFLECTOR:Foil Tape Antennas

  =20

  Chris,

  =20

  According the the plans, the VOR antennas are to be built into the =
bottom of the wing.  Obviously, not a place where you could cover them =
with any type of foil.

  =20

  I did install my localizer antenna in the cabin floor.  Thanks for the =
tip.

  =20

  Best,

  =20

  Andy

    -----Original Message-----
    From: reflector-admin@tvbf.org [mailto:reflector-admin@tvbf.org]On =
Behalf Of Chris Martin
    Sent: Saturday, May 03, 2003 1:00 PM
    To: reflector
    Subject: REFLECTOR:Foil Tape Antennas

    This note is for those of you that are using the foil tape antennas =
as designed by Jim Weir. This is the standard antenna system in the =
Velocities and I am sure all of you are using them in some form. I have =
always been unhappy with the performance of my VOR antennas mounted on =
my fuselage floor and finally wrote to Jim Weir to seek his advice. I =
wrote:

    =20

    "Jim, my question is this. The two VOR antennas in question are =
mounted on the floor of the fiberglass fuselage. Over the floor I have I =
have laid sound insulation and carpet. The sound insulation has a =
aluminum foil layer on each side. Is the foil the probable source of the =
antenna failure? "

    =20

    Jim's response was "Without a doubt!"

    =20

    I wonder how many of you have made the same mistake I made in =
diligently building your antennas to Jim Weir's plans and then =
mistakenly covering them with a foil backed sound insulation. The foil =
backed sound insulation was the one recommended by Velocity when I =
installed my interiors in 2000.

    =20

    Hope this helps some of you.

    =20

    Chris Martin

    Velocity XL RG

    330 hours flying

    =20

    =20

    ---=20

    --- christophercmartin@earthlink.net

    --- EarthLink: It's your Internet.

    =20

    _______________________________________________ To change your email =
address, visit http://www.tvbf.org/mailman/listinfo/reflector Visit the =
gallery! tvbf:jamaicangoose=20


------=_NextPart_000_000C_01C3124B.2DAD86E0
Content-Type: text/html;
	charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable

<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML xmlns=3D"http://www.w3.org/TR/REC-html40" xmlns:o =3D=20
"urn:schemas-microsoft-com:office:office" xmlns:w =3D=20
"urn:schemas-microsoft-com:office:word"><HEAD>
<META http-equiv=3DContent-Type content=3D"text/html; =
charset=3Diso-8859-1">
<META content=3DWord.Document name=3DProgId>
<META content=3D"MSHTML 5.50.4522.1800" name=3DGENERATOR>
<META content=3D"Microsoft Word 10" name=3DOriginator><LINK=20
href=3D"cid:filelist.xml@01C3123D.B71B4AB0" rel=3DFile-List><!--[if gte =
mso 9]><xml>
 <o:OfficeDocumentSettings>
  <o:DoNotRelyOnCSS/>
 </o:OfficeDocumentSettings>
</xml><![endif]--><!--[if gte mso 9]><xml>
 <w:WordDocument>
  <w:SpellingState>Clean</w:SpellingState>
  <w:GrammarState>Clean</w:GrammarState>
  <w:DocumentKind>DocumentEmail</w:DocumentKind>
  <w:EnvelopeVis/>
 </w:WordDocument>
</xml><![endif]-->
<STYLE>@font-face {
	font-family: Tahoma;
}
@font-face {
	font-family: MS Sans Serif;
}
@page Section1 {size: 8.5in 11.0in; margin: 1.0in 1.25in 1.0in 1.25in; =
mso-header-margin: .5in; mso-footer-margin: .5in; mso-paper-source: 0; }
P.MsoNormal {
	FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman"; =
mso-style-parent: ""; mso-pagination: widow-orphan; =
mso-fareast-font-family: "Times New Roman"
}
LI.MsoNormal {
	FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman"; =
mso-style-parent: ""; mso-pagination: widow-orphan; =
mso-fareast-font-family: "Times New Roman"
}
DIV.MsoNormal {
	FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman"; =
mso-style-parent: ""; mso-pagination: widow-orphan; =
mso-fareast-font-family: "Times New Roman"
}
A:link {
	COLOR: blue; TEXT-DECORATION: underline; text-underline: single
}
SPAN.MsoHyperlink {
	COLOR: blue; TEXT-DECORATION: underline; text-underline: single
}
A:visited {
	COLOR: blue; TEXT-DECORATION: underline; text-underline: single
}
SPAN.MsoHyperlinkFollowed {
	COLOR: blue; TEXT-DECORATION: underline; text-underline: single
}
P {
	FONT-SIZE: 12pt; MARGIN-LEFT: 0in; MARGIN-RIGHT: 0in; FONT-FAMILY: =
"Times New Roman"; mso-pagination: widow-orphan; =
mso-fareast-font-family: "Times New Roman"; mso-margin-top-alt: auto; =
mso-margin-bottom-alt: auto
}
SPAN.EmailStyle18 {
	COLOR: navy; FONT-FAMILY: Arial; mso-style-type: personal-reply; =
mso-style-noshow: yes; mso-ansi-font-size: 10.0pt; mso-bidi-font-size: =
10.0pt; mso-ascii-font-family: Arial; mso-hansi-font-family: Arial; =
mso-bidi-font-family: Arial
}
SPAN.GramE {
	mso-style-name: ""; mso-gram-e: yes
}
DIV.Section1 {
	page: Section1
}
</STYLE>
<!--[if gte mso 10]>
<style>
 /* Style Definitions */=20
 table.MsoNormalTable
	{mso-style-name:"Table Normal";
	mso-tstyle-rowband-size:0;
	mso-tstyle-colband-size:0;
	mso-style-noshow:yes;
	mso-style-parent:"";
	mso-padding-alt:0in 5.4pt 0in 5.4pt;
	mso-para-margin:0in;
	mso-para-margin-bottom:.0001pt;
	mso-pagination:widow-orphan;
	font-size:10.0pt;
	font-family:"Times New Roman";}
</style>
<![endif]--></HEAD>
<BODY lang=3DEN-US style=3D"tab-interval: .5in" vLink=3Dblue link=3Dblue =

bgColor=3D#ffffff>
<DIV><FONT size=3D2>I think that we are having some nomenclature =
problems here. Of=20
course the localizer uses the same antenna at the VOR. The localizer =
frequencies=20
are simply the bottom end of the nav frequency band. The glide slope =
receiver=20
can also be split off of the nav antenna but it is probably better to =
have a=20
separate antenna. If a separate glide slope antenna is used it is a =
short one=20
which is usually mounted between the bottom of the windshield&nbsp; and =
the=20
canard doghouse. The long antenna that is usually mounted on the cabin =
floor is=20
the marker beacon antenna.</FONT></DIV>
<BLOCKQUOTE dir=3Dltr=20
style=3D"PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; =
BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
  <DIV style=3D"FONT: 10pt arial">----- Original Message ----- </DIV>
  <DIV=20
  style=3D"BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: =
black"><B>From:</B>=20
  <A title=3Dtmartino@troubleshooter.com=20
  href=3D"mailto:tmartino@troubleshooter.com">Tom Martino</A> </DIV>
  <DIV style=3D"FONT: 10pt arial"><B>To:</B> <A =
title=3Dreflector@tvbf.org=20
  href=3D"mailto:reflector@tvbf.org">reflector@tvbf.org</A> </DIV>
  <DIV style=3D"FONT: 10pt arial"><B>Sent:</B> Sunday, May 04, 2003 1:03 =
PM</DIV>
  <DIV style=3D"FONT: 10pt arial"><B>Subject:</B> RE: REFLECTOR:Foil =
Tape=20
  Antennas</DIV>
  <DIV><BR></DIV>
  <DIV class=3DSection1>
  <P class=3DMsoNormal><FONT face=3DArial color=3Dnavy size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; COLOR: navy; FONT-FAMILY: Arial">I was told =
you could=20
  use the VOR antenna for the localizer and you didn&#8217;t need a =
separate=20
  antenna.<o:p></o:p></SPAN></FONT></P>
  <P class=3DMsoNormal><FONT face=3DArial color=3Dnavy size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; COLOR: navy; FONT-FAMILY: =
Arial"><o:p>&nbsp;</o:p></SPAN></FONT></P>
  <DIV>
  <P class=3DMsoNormal><FONT face=3D"Times New Roman" color=3Dnavy =
size=3D3><SPAN=20
  style=3D"FONT-SIZE: 12pt; COLOR: navy; mso-no-proof: =
yes">&nbsp;</SPAN></FONT><o:p></o:p></P></DIV>
  <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DTahoma =
size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; FONT-FAMILY: Tahoma">-----Original=20
  Message-----<BR><B><SPAN style=3D"FONT-WEIGHT: bold">From:</SPAN></B> =
Andy=20
  Millin [mailto:amillin@net-link.net<SPAN class=3DGramE>] <BR><B><SPAN=20
  style=3D"FONT-WEIGHT: bold">Sent</SPAN></B></SPAN><B><SPAN=20
  style=3D"FONT-WEIGHT: bold">:</SPAN></B> Sunday, May 04, 2003 7:45=20
  AM<BR><B><SPAN style=3D"FONT-WEIGHT: bold">To:</SPAN></B> <A=20
  href=3D"mailto:reflector@tvbf.org">reflector@tvbf.org</A><BR><B><SPAN=20
  style=3D"FONT-WEIGHT: bold">Subject:</SPAN></B> RE: REFLECTOR<SPAN=20
  class=3DGramE>:Foil</SPAN> Tape Antennas</SPAN></FONT></P>
  <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"Times =
New Roman"=20
  size=3D3><SPAN style=3D"FONT-SIZE: =
12pt"><o:p>&nbsp;</o:p></SPAN></FONT></P>
  <DIV>
  <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DArial =
color=3Dblue=20
  size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: =
Arial">Chris,</SPAN></FONT><FONT=20
  face=3D"MS Sans Serif" size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
  <DIV>
  <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
  size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
  <DIV>
  <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DArial =
color=3Dblue=20
  size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: Arial">According =
the the=20
  plans, the VOR antennas are to be built into the bottom of the =
wing.&nbsp;=20
  Obviously, not a place where you could cover them with any type of=20
  foil.</SPAN></FONT><FONT face=3D"MS Sans Serif" size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
  <DIV>
  <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
  size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
  <DIV>
  <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DArial =
color=3Dblue=20
  size=3D2><SPAN style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: =
Arial">I did=20
  install my localizer antenna in the cabin floor.&nbsp; Thanks for the=20
  tip.</SPAN></FONT><FONT face=3D"MS Sans Serif" size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
  <DIV>
  <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
  size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
  <DIV>
  <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DArial =
color=3Dblue=20
  size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: =
Arial">Best,</SPAN></FONT><FONT=20
  face=3D"MS Sans Serif" size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
  <DIV>
  <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
  size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
  <DIV>
  <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DArial =
color=3Dblue=20
  size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: =
Arial">Andy</SPAN></FONT><FONT=20
  face=3D"MS Sans Serif" size=3D2><SPAN=20
  style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
  <BLOCKQUOTE style=3D"MARGIN-TOP: 5pt; MARGIN-BOTTOM: 5pt">
    <P class=3DMsoNormal=20
    style=3D"MARGIN-BOTTOM: 12pt; MARGIN-LEFT: 0.5in; MARGIN-RIGHT: 0in; =
mso-margin-top-alt: 0in"><FONT=20
    face=3DTahoma size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: Tahoma">-----Original=20
    Message-----<BR><B><SPAN style=3D"FONT-WEIGHT: =
bold">From:</SPAN></B>=20
    reflector-admin@tvbf.org [mailto:reflector-admin@tvbf.org]<B><SPAN=20
    style=3D"FONT-WEIGHT: bold">On Behalf Of </SPAN></B>Chris =
Martin<BR><B><SPAN=20
    style=3D"FONT-WEIGHT: bold">Sent:</SPAN></B> Saturday, May 03, 2003 =
1:00=20
    PM<BR><B><SPAN style=3D"FONT-WEIGHT: bold">To:</SPAN></B>=20
    reflector<BR><B><SPAN style=3D"FONT-WEIGHT: =
bold">Subject:</SPAN></B>=20
    REFLECTOR:Foil Tape Antennas</SPAN></FONT><FONT face=3D"MS Sans =
Serif"=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">This note=20
    is for those of you that are using the foil tape antennas as =
designed by Jim=20
    Weir. This is the standard antenna system in the Velocities and I am =
sure=20
    all of you are using them in some form. I have always been unhappy =
with the=20
    performance of my VOR antennas mounted on my fuselage floor and =
finally=20
    wrote to Jim Weir to seek his advice. I=20
    wrote:<o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">"Jim, my=20
    question is this. The two VOR antennas in question are mounted on =
the floor=20
    of the fiberglass fuselage. Over the floor I have I have laid sound=20
    insulation and carpet. The sound insulation has a aluminum foil =
layer on=20
    each side. Is the foil the probable source of the antenna=20
    failure?</SPAN></FONT><FONT face=3DArial color=3Dblue size=3D2><SPAN =

    style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: =
Arial">&nbsp;"</SPAN></FONT><FONT=20
    face=3D"MS Sans Serif" size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DArial =
color=3Dblue=20
    size=3D2><SPAN style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: =
Arial">Jim's=20
    response was "Without a doubt!"</SPAN></FONT><FONT face=3D"MS Sans =
Serif"=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DArial =
color=3Dblue=20
    size=3D2><SPAN style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: =
Arial">I=20
    wonder how many of you have made the same mistake I made in =
diligently=20
    building your antennas to Jim Weir's plans and then mistakenly =
covering them=20
    with a foil backed sound insulation. The foil backed sound =
insulation was=20
    the one recommended by Velocity when I installed my interiors in=20
    2000.</SPAN></FONT><FONT face=3D"MS Sans Serif" size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DArial =
color=3Dblue=20
    size=3D2><SPAN style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: =
Arial">Hope=20
    this helps some of you.</SPAN></FONT><FONT face=3D"MS Sans Serif" =
size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DArial =
color=3Dblue=20
    size=3D2><SPAN style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: =
Arial">Chris=20
    Martin</SPAN></FONT><FONT face=3D"MS Sans Serif" size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DArial =
color=3Dblue=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: Arial">Velocity =
XL=20
    RG</SPAN></FONT><FONT face=3D"MS Sans Serif" size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3DArial =
color=3Dblue=20
    size=3D2><SPAN style=3D"FONT-SIZE: 10pt; COLOR: blue; FONT-FAMILY: =
Arial">330=20
    hours flying</SPAN></FONT><FONT face=3D"MS Sans Serif" =
size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'"><o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">---=20
    <o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">--- <A=20
    =
href=3D"mailto:christophercmartin@earthlink.net">christophercmartin@earth=
link.net</A><o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">---=20
    EarthLink: It's your Internet.<o:p></o:p></SPAN></FONT></P></DIV>
    <DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">&nbsp;<o:p></o:p></SPAN></FONT></P></DIV>
    <P class=3DMsoNormal style=3D"MARGIN-LEFT: 0.5in"><FONT face=3D"MS =
Sans Serif"=20
    size=3D2><SPAN=20
    style=3D"FONT-SIZE: 10pt; FONT-FAMILY: 'MS Sans =
Serif'">_______________________________________________=20
    To change your email address, visit=20
    http://www.tvbf.org/mailman/listinfo/reflector Visit the gallery!=20
    tvbf:jamaicangoose=20
<o:p></o:p></SPAN></FONT></P></BLOCKQUOTE></DIV></BLOCKQUOTE></BODY></HTM=
L>

------=_NextPart_000_000C_01C3124B.2DAD86E0--