REFLECTOR: Electrical system

[David Rene Dugas]

Enjoyed the read. 

René Dugas
Sent from an Apple REALLY smart phone. 

On Jun 29, 2013, at 12:11 PM, Dave T Nelson <dtnelson at us.ibm.com> wrote:

> This is an excellent area for KISS.... Keep It SIMPLE!
> 
> In my installation, I used two connection blocks in the area behind the instrument panel for both 12V and ground (4 total), one of each flavor on the left and on the right.  I made them myself by soldering brass screws into a brass plate.  I then used ring terminals on the wire ends.  The terminals are then held tight with MS21042 nuts.  The idea is to avoid having to have wires seeking 12V or ground from having to cross the whole panel from the left side to the right (or vise-versa).  The ground system should be simple - everything has only one grounding point (to avoid ground loops).  On both power and ground, the buss bars are powered (or grounded) via two wires for redundancy.  
> 
> I used switch circuit breakers instead of switches with separate circuit breakers (or fuses).  I wouldn't recommend that... I've had a couple of them fail.  
> 
> I used circuit breakers instead of fuses.  My reasoning was that I want to be able to see at a glance if one had popped (hard to do with a fuse).  I wish I'd used the type that allow you to pull the end of the circuit breaker to switch a circuit off.  
> 
> Don't buy used circuit breakers!
> 
> Use real aviation grade wire, not Radioshack junk.  
> 
> I used, carefully and religiously, a wire size chart.  I've seen many, many installations where folks use wire of way to low of a gauge (too thick and heavy).  You'll be surprised how often you can use 20 or even 22 gauge based on the current requirements.  Make sure the wiring chart you use is for bundled wire, not single strand.  Make sure you use the right size terminal for each wire.  
> 
> I sized the circuit breakers for the load, not for the wire carrying capacity.  There has been some debate on this, as Nuckolls would size the fuse/circuit breaker for the wire, not the load.  IMHO I'm trying to protect the expensive load (radio), and the wire will always be sized with a much greater capacity anyway... so the wire is protected if I size the fuse for the load.  
> 
> Pay attention to wire dress... think about your major wiring lanes... try to get the wiring to all flow into and out of a lane... which allows you to secure a bundle instead of trying to secure individual wires.  
> 
> Ensure you've got wires secured within a few inches of the connection point.  You don't want vibration load to be taken by the connector.  It will fail for sure.
> 
> If you are handy with a soldering iron, don't be afraid to use it - as long as you are securing the soldered joint from vibration.  
> 
> As I said, I chose ring terminals instead of spades... I want to be able to count on a lock nut for security.  Don't by hardware store connectors - don't!  Get good quality bimetal crimp connectors (3M makes good ones).  Use a real rachetting crimp tool, not a hardware store special.  
> 
> I *hate* cable ties... no matter how carefully you cut the ends off, they'll leave sharp edges that'll get you at some point.  I used nylon wire tie string instead... it works great, it's easy to use, and it'll never bite you.  
> 
> The only relays in my plane are the main electrical and starter solenoids.  I know they've gotten much more reliable through the years, but I'm still shy of using them.  I don't know where they'd do something that there isn't an easy way to do without them.  
> 
> I grew up as a ham radio operator, worked in a TV repair shop through HS, and as a technician wiring satellites in college.  That (and my BSEE) form my opinions on this stuff.  I enjoy pulling wire and I believe I'm good at it.  I'm coming up on 1100 hours on my Velocity, and had 900+ hours on a Varieze I built first - with zero wiring induced issues.
> 
> Happy to discuss if you'd like to call.
>   
> Dave
> 
> Dave T. Nelson
> T/L 553-4327, Voice 507-253-4327, Fax 507-253-3648
> Program Director, ISC ECAT NPI & Test Engineering
> 
> ----- Message from Reiff Lorenz <Reiff at Lorenz.com> on Sat, 29 Jun 2013 09:55:22 -0400 -----
> 
> To:
> "reflector at tvbf.org" <reflector at tvbf.org>
> Subject:
> REFLECTOR: Electrical system - basic components
>  
> I'm starting work on the electrical system. I could use some recommendations on what to purchase (or how to make) these items and where you installed them:
>  
> ·         Main bus
> ·         Main ground block
> ·         Firewall ground block
> ·         Avionics ground
>  
> I'm going to use the Vertical Power system for switching & circuit breakers so a combination bus/CB system won't be necessary. Should I just buy some copper bar and drill screw-holes in it? Is there a good, basic bus product that works well? Where did you mount it and how did you protect the power buses from accidental grounding?
>  
> Thanks!
>  
>  
> Reiff Lorenz, Dayton, OH
> Velocity XL-RG, 45% complete
> Currently working on: Mounting the battery, main contactor, starter contactor, and RG control system.
>  
> Velocity Owners and Builders Association
> http://www.VelocityOwners.com
> _______________________________________________
> To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector
> 
> Visit the gallery!  www.tvbf.org/gallery
> user:pw = tvbf:jamaicangoose
> Check new archives: www.tvbf.org/pipermail
> Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.tvbf.org/mailman/private/reflector/attachments/20130629/b412bd7e/attachment.html>