REFLECTOR: First flight

Sun Jun 10 15:53:00 CDT 2012

Chris,

Congratulations on your first flight!!!

It sound like you have a Dynon Skyview.  If you do, you should be using its
engine recording feature to record your engine parameters while you are
flying.  You will need a laptop to catch the data streaming out one of the
serial ports.  It's very fast at up to 16 records per second.  Read page
19-8 of the System Instillation guide.  If you have a Windows based laptop
(XP or earlier) you can use the included HyperTerminal program to save the
data as a text file.

It's a little easier than snapping pictures of your screen while flying.

Contact me offline if you want help.

Darrell

From: reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org] On
Behalf Of Chris Barber
Sent: Sunday, June 10, 2012 8:35 AM
To: Velocity Aircraft Owners and Builders list
Subject: Re: REFLECTOR: First flight

I have two oil coolers already.  The standard cooler mounted under the
aircraft laid flat with the radiator to make one large unit and fed with a
large ram air scoop on the bottom of the cowl.  I also have a second oil
cooler (standard aircraft cooler as provided by Velocity) in the nose per
planes plumbed in parallel.  It was originally plumbed in series but since
it has smaller fittings, it was causing a pressure issue and oil would seep
out from around my oil filter.

I got some pondering to do.

I was just looking at the distorted video I took while in the pattern on
downwind.  It is only a few seconds long.  Very hard to see some of the
info.  It does show my rpm got up to 6870 rpm but the map on the RWS monitor
was only indicating 24.7. (?)  I am running a spring in the waste gate at
1.5 lbs. Coolant temps were 187 degrees while oil was 224 degrees.  GPS
speed showed 128 kts per the Dynon.  

The IVO in-flight adjustable prop was at full fine. The IVO pith range is 45
- 105 and IIRC it is 68 inches.

Chris

  _____  

From: reflector-bounces at tvbf.org [reflector-bounces at tvbf.org] on behalf of
John Dibble [aminetech at bluefrog.com]
Sent: Sunday, June 10, 2012 7:27 AM
To: Velocity Aircraft Owners and Builders list
Subject: Re: REFLECTOR: First flight

I second that for the oil cooler.  Are you using the standard oil cooler?  I
think a problem is that the standard oil cooler is intended for engines in
the 180-200 hp range and for engines with more hp, a larger cooler is
needed.  It doesn't take much increase in cooler size to make a big
difference in cooling, so a larger cooler (1" taller) may be all you need
and simpler than adding a second.

John

On 6/9/2012 8:28 PM, Al Gietzen wrote: 

Way to go Chris!!  That is a life-changing milestone.  Congratulations! 

Reminiscent of 1st flight with my plane - oil temp hit 225 and ended the
flight with one turn around the patch. As you said; not critical, but you
don't want to run a rotary very long above that temp.  For me it took some
work on the scoop; and eventually a second oil cooler to keep things in the
comfort zone on a hot day.  You might consider an auxiliary oil/coolant heat
exchanger. 

Now that you are a "real" pilot, get out there at 0700 when air temp is
below 80 and maybe you can fly long enough to enjoy it. 

Al 

-----Original Message-----
From: reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org] On
Behalf Of Chris Barber
Sent: Saturday, June 09, 2012 9:50 AM
To: REFLECTOR
Subject: REFLECTOR: First flight

Cleared to take active and hold. Taxied out. Lined up castering nose wheel
down center stripe. Cleared to take off. Added power and engine smoothly ran
up. Airspeed coming in. 30 kts...50 kts ....60 kts, approximate rotation
speed. Lots of runway (9000 ft).....hold it....70 kts....72 kts... Slight
pull on the yoke....AIRBORNE!!! Leaped into ground effect. Screw this,
pulled back on yoke and I am climbing. Jiggled the yoke a bit to verify
control authority. 

Climbed to about 400 feet and turned right pattern to crosswind. The Dynon
altitude and airspeed seem to be working. That's reassuring. Pattern
altitude is only 600 feet and I was there already as I turned to downwind.
Leveled off and noticed the clouds were lower than reported and appeared on
the ground. Also, noticed coolant temps had dropped to 190....but oil temps
were flashing at me and had reached 225 (synthetic Royal Purple). Damn. Ok.
Fly the airplane, the oil is not at not a critical level. , but let's just
finish the pattern and land. I grabbed my phone while on downwind and
attempted to record some data but while I can hear the engine the video is
awful....uh, in my defense, I was a bit distracted and way more concerned
with flying. I called the tower and informed them I was coming in. I think
they were looking out for me since as I turned to base I noticed the fire
department staged just off the runways threshold

I noted I was a bit far out on down wind so I stared easing over to turn
base. Wow. I really overshot it as I blew by the runway and had to use full
right rudder to get back to the runway. I wish I had had more rudder. In
hindsight I think I was not using much aileron as I was cognoscente that I
had no idea of stall characteristics so I did not yet wish too strep a turn.
I was able to get over the runway and dump some altitude as I got over the
numbers and pulled power. Crap, I am fast. I am lined up and right on the
numbers but at 95 kts. I come and touchdown and bounced. Pulled power to
idles and settled down easily but fast at 90 and rolled out and exited at
Delta. The tower was clearing me back to the city hangars as I was exiting
the active. I taxi back and noticed the oil temps had decreased but I don't
recall how much, just noticed they were lower.

I got back to my hangar and popped the door and shut her down. The engine
went silent without any hissing or gushing. 

I called my mom. 

I am mowing informing the world. 

I did a walk around and did not see anything missing. I am about to pull the
cowl and check things out. 

I did notice I did not develop a slight hand shaking untill after I landed
and exited the aircraft. ;-) Hey, how about that, it really is an aircraft
now. Ten years to the day following delivery. 

Thank you for your support. 

Christopher Barber, JD

Houston, Ellington Field (EFD)

Velocity N17010

Turbo Rotary 13b

RWS Re-drive and engine computers

Dynon Skyview

Mistral intake

Sent from my iPhone 4

_______________________________________________
To change your email address, visit
http://www.tvbf.org/mailman/listinfo/reflector

Visit the gallery!  www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.tvbf.org/mailman/private/reflector/attachments/20120610/26779c5a/attachment-0001.htm>