REFLECTOR: AIR INTAKE DUCT

[Al Gietzen]

. How do I determine the cfm of the 3" hose. Is it 8230 cfm?I have a K&N
filter #33-2060 which is mounted right in the belly scoop. The length of
hose from there to the fuel servo is 26". I am using skeet tube so the
inside of the hose is fairly smooth. Do you think the 2 1/2" is large enough
or do you think I need to go to the 3". 

 

The volumetric air flow is determined by the engine displacement and the
rpm.  What we working on here is reducing the pressure drop to the engine
for a slight increase in the “mass” air flow (the density of the air) into
the cylinders.  I think the 2 ½” is restrictive, and 3” would be a definite
improvement.  You’d also like to avoid abrupt contractions and expansions;
like from the filter to the duct, from the duct to the fuel servo.

 

That filter may be a bit restrictive, especially when dirty, so at the least
you’d like to change it fairly frequently.

 

Best,

Al 

Lou Stedman
Velocity N7044Q
Olean, NY

----- Original Message ----- 

From: Al Gietzen <mailto:ALVentures at cox.net>  

To: 'Velocity Aircraft <mailto:reflector at tvbf.org>  Owners and Builders
list' 

Sent: Thursday, April 17, 2008 12:52 AM

Subject: Re: REFLECTOR: AIR INTAKE DUCT

 

I have a tech. question.  I have a LYC. IO-360. I am replacing the Skeet
duct which runs from the belly scoop, through my K&N filter, through my
alternate air T, and into the throat of my fuel servo. The hose that is on
it now is 2 1/2". My A&P tells me it should be a minimum of 3" diameter, yet
the throat opening of the fuel servo is only 2 3/8". How can I determine
what is the right size to supply needed air flow?

Lou Stedman

 

Lou;

 

It’s all about pressure drop.  Pressure drop in the induction path directly
reduces the amount of air/fuel charge entering the cylinder. The throat of
the fuel servo is very short, so there is not a lot of frictional loss
there, and you want high velocity at that point for fuel dispersion, etc. It
sounds like you have a fairly torturous path for the induction air to travel
before getting to the intake manifold.

 

What is the right size? Well, that’s a bit complex.  You could measure the
pressure at the entrance to the fuel servo, and if it is more then 1” of HG
less than the pressure at the entrance to the scoop, the loss is probably
higher than you’d like.  Or you could do some analysis based on the engine
displacement, rpm, air flow velocity, and compute the pressure drop.  Not
very easy.  

 

But just a back of the envelope analysis - your engine would like to take in
180 cubic inches of air each revolution.  At 2700 rpm that’s 280 cubic ft
per min (cfm). You 2 ½” duct has an area of only 0.034 sq ft; so the
velocity in there would be 8230 ft/min, or about 95 mph. Depending on the
length of tube, that could be considerable friction and turbulence loss,
especially if the inner surface is not real smooth.  And does it also have
to make a turn? More loss.  How big a filter?  Pressure loss there as well.

 

A 3” diameter would slow the velocity by 30%; a big help.  3 ½” would be
even better.  Pressure losses generally go as the square of the velocity.

 

FWIW;

 

Al


  _____  


_______________________________________________
To change your email address, visit
http://www.tvbf.org/mailman/listinfo/reflector

Visit the gallery!  www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.tvbf.org/mailman/private/reflector/attachments/20080417/3fee681d/attachment-0001.htm