REFLECTOR: Intake Measurement

[Rene Dugas via Reflector]

I have no boots with about 3/16" gaps and no cooling issues.  I've considered it but worry about it tearing and falling on the exhaust with subsequent fire.  If I had a problem that would probably be my first attempt at a fix though.



Sent from Rene's iPad. A pleasure.  Go Apple.


> On Jan 8, 2015, at 1:35 PM, paul barfknecht via Reflector <reflector at tvbf.org> wrote:
> 
> My nacas extend about an inch into the engine compartment. My downdraft tunnels are installed by sliding over the nacas forward then pivoted down to attach (with all those beautiful screws) to the plenum. The tube over tube fit is a smidge less than snug at the firewall. If I am getting movement of the engine relative to the firewall there is the allowance. Clearance between the downdraft tunnels and the cowling is about a quarter inch as I recall.
> 
> 
> -----Original Message-----
> From: ajlz72756 at yahoo.com
> Sent: Thu, 8 Jan 2015 09:50:00 -0600
> To: ceraygun at inbox.com, tmann at n200lz.com, reflector at tvbf.org
> Subject: Re: REFLECTOR: Intake Measurement
> 
> Beautiful workmanship, my question is, I keep seeing all of these photo’s of the down draft cooling plenums, without any rubber booted connection between the engine and the NACA scoop connection at the firewall. I have seen photo’s of the plenums with a rubber boot installed. So for those that I am seeing without, I know that my 300hp IO540 engine, using the standard MT three blade prop, is torqueing against the engine mount, at least 3/8 inch at full power, I know this because of the size holes I have had to cut around my exhaust pipes to keep them from hitting my cowling. My exhaust Exit holes started out with a 1/4 inch clearance all the way around, and I had to keep enlarging them, they are now oblong,  in the direction that the engine is twisting. It also seems to me that without some sort of rubber booted connection, that the engine vibration alone, would rip the connection off of the firewall.
>  
> My thoughts, others using the NACA down draft cooling will have to weigh in on this issue.
>  
> -----------------------------------------
> Andrew Ellzey
> N151AJ IO540 300hp armpit updraft cooling
>  
> From: paul barfknecht via Reflector
> Sent: Wednesday, January 07, 2015 4:42 PM
> To: Thomas Mann ; Velocity Aircraft Owners and Builders list ; Velocity Reflector
> Subject: Re: REFLECTOR: Intake Measurement
>  
> I don't have the measurement, but thought you might be interested in a photo of my plenum on an SUV with an io360.  Ken Mishler , a Velocity Jedi Master created this masterpiece (with a little assistance from me) which has resulted in no concerns regarding cooling on my plane. removable sections allow good access to the top and front of the engine.
> Paul Barfknecht
> 
> 
> 
> Free 3D Earth Screensaver
> Watch the Earth right on your desktop! Check it out at www.inbox.com/earth
> _______________________________________________
> To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector
> 
> Visit the gallery!  www.tvbf.org/gallery
> user:pw = tvbf:jamaicangoose
> Check new archives: www.tvbf.org/pipermail
> Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
> 
> _______________________________________________
> To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector
> 
> Visit the gallery!  www.tvbf.org/gallery
> user:pw = tvbf:jamaicangoose
> Check new archives: www.tvbf.org/pipermail
> Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.tvbf.org/mailman/private/reflector/attachments/20150108/cadf7837/attachment-0001.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image1.jpeg
Type: image/jpeg
Size: 35897 bytes
Desc: not available
URL: <http://www.tvbf.org/mailman/private/reflector/attachments/20150108/cadf7837/attachment-0001.jpeg>