REFLECTOR: "Stuck" Franklin

[James Traynor]

When you find the stuck valve use a very good antisense lubricant and work the valve if you can very slowly for days until free. Work the engine around a lot to free up other valves. You may wont to lubricate the other valves at this time. 
I had a 1949 flat head Pontiac that had not run for 12 years when I got it. Dad pulled the plugs and added a antisense lubricant and sprayed the valves through the side inspection plate. After a week we turn over by hand and freed up the engine added good fuel primed and I could not be leave that it started first try. 
It takes a lot to bend a valve and you will see marks on the top of the piston if you have a scope. Look to see if some one tried to turn over with the starter and had valve to piston hit. If a hard hit happened the connecting rod may be bent.
Good luck and go slow it will save you money in the end
 
James
From: humeno at microsoft.com
To: reflector at tvbf.org
Date: Tue, 4 Feb 2014 21:36:40 +0000
Subject: Re: REFLECTOR: "Stuck" Franklin









Thanks.  I didn’t pull the prop very hard knowing that stuck valves were a distinct possibility.  We will follow your suggestion to see if this is the case.
 


From: reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org]
On Behalf Of Laurence Coen

Sent: Tuesday, February 04, 2014 9:23 AM

To: Velocity Aircraft Owners and Builders list

Subject: Re: REFLECTOR: "Stuck" Franklin


 

Hiroo,


 


I still suspect a stuck valve.  If you turn the engine to the stop point and check which pistons are in the up position and remove the valve covers on those cylinders
 you can check the rockers to see if the valves are fully retracted.  The only thing in the engine that happens at 180 deg. rotation is the crank and what is attached to it (pistons).  Since you have pulled the plugs, it can't be hydraulic lock.


 


Larry Coen


N136LC


Franklin/IVO



 



From:
Hiroo Umeno



Sent: Monday, February 03, 2014 11:34 PM


To:
Velocity Aircraft Owners and Builders list



Subject: REFLECTOR: "Stuck" Franklin




 

Franklin Experts,
 
We are just starting to re-activate an aircraft that has sat for 7 years in a hangar storage.  When we flew it last, the aircraft flew well and the engine performed as expected.  This an installation on a
 Velocity and it has the oil cooler bypass fix that was needed to operate at proper oil temperature.
 
The engine is a PZL built 6A-350 that has approximately 27 hours since major overhaul / rebuild.  The aircraft has engine driven fuel pump and dual slick magneto ignition (no electronic ignition). 

 
When we pulled the plugs off and attempted to hand turn the prop, we discovered that the prop will not complete the full turn.  Rather, there is a definite stop point at 180 degree rotation in either direction. 
 Inspection of the cylinders reveal no piston contact with valves and no obvious blockage.  No new parts have been installed since it was last operated. 

 
I am wondering if there is a “likely suspect” that we should look at first.
 
Hiroo



_______________________________________________

To change your email address, visit 
http://www.tvbf.org/mailman/listinfo/reflector



Visit the gallery!  www.tvbf.org/gallery

user:pw = tvbf:jamaicangoose

Check new archives: www.tvbf.org/pipermail

Check old archives: 
http://www.tvbf.org/archives/velocity/maillist.html




_______________________________________________
To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector

Visit the gallery!  www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html 		 	   		  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.tvbf.org/mailman/private/reflector/attachments/20140205/87cd3654/attachment-0001.html>