REFLECTOR: Engine install pictures

[Glenn Babcock]

Peter,

I have the same aircraft, engine and prop with 500 hours on it.  Email me at grb99 at icloud.com and I’ll get you whatever you need.  Where are you located?

Regards,
Glenn


On Oct 25, 2013, at 9:09 AM, Peter Braswell <peter.braswell at gmail.com> wrote:

> Reiff,
> Certainly.  I actually was thinking about this after I sent out the email ... I should have told you all what I was installing.
> 
> Here are the particulars:
> Plane: SERG
> Engine: IO-360
> Prop: MT w/Hydraulic governor.  The governor is on the COP side of the plane.   
> Configuration: Conventional controls (center stick and engine controls on the P side.
> 
> The factory suggested that we just run the control cables down the tunnel which we've done.  I've got a pretty good idea of where the brackets mount and what they look like, but I'm seeking pictures to verify.  The mystery to me is the induction stuff.  According to the factory, there is no supplied airbox, inlet or anything like that.  That's all up to the builder.  They suggest using SKET (sp?) tubing, not SCAT tubing as the SCAT tubing could collapse if the inset wires pull out of the liner. 
> 
> Anything that you all think would help me get a handle on this would be greatly appreciated!
> 
> All the best,
> Peter 
> 
> ------------------------------------------------------------------------
> "It's a Jungle Up There": www.zuluworks.com
> ------------------------------------------------------------------------
> 
> 
> On Fri, Oct 25, 2013 at 8:26 AM, Reiff Lorenz <Reiff at lorenz.com> wrote:
> Peter,
> 
> Can you tell me what engine you're installing? Normal throttle location, or do you have side sticks & center throttle?
> 
> Thanks!
> 
> Reiff Lorenz
> 
> Sent from my phone; please excuse the brevity.
> ________________________________
> From: Peter Braswell<mailto:peter.braswell at gmail.com>
> Sent: 10/24/2013 8:34 PM
> To: Velocity Aircraft Owners and Builders list<mailto:reflector at tvbf.org>
> Subject: REFLECTOR: Engine install pictures
> 
> Hi all,
> So I'm in the middle of installing my engine doing my best to blissfully ignore all the chatter about the difficulties involved with getting insurance.
> 
> What I was wondering was if anybody has any good pics of the air induction system and some detailed shots of the control cable routing.
> 
> I have looked at the pics on the velocity site, but I was wondering if anybody has any additional to augment those.
> 
> Many thanks,
> Peter
> 
> ------------------------------------------------------------------------
> "It's a Jungle Up There": www.zuluworks.com<http://www.zuluworks.com>
> ------------------------------------------------------------------------
> 
> _______________________________________________
> To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector
> 
> Visit the gallery!  www.tvbf.org/gallery
> user:pw = tvbf:jamaicangoose
> Check new archives: www.tvbf.org/pipermail
> Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
> 
> _______________________________________________
> To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector
> 
> Visit the gallery!  www.tvbf.org/gallery
> user:pw = tvbf:jamaicangoose
> Check new archives: www.tvbf.org/pipermail
> Check old archives: http://www.tvbf.org/archives/velocity/maillist.html

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.tvbf.org/mailman/private/reflector/attachments/20131026/2d424f1c/attachment.html>