REFLECTOR: Prop dia
steve korney
s_korney at hotmail.com
Thu Jun 6 12:37:24 CDT 2013
Thanks.... Now it make more sense...
Steve
Date: Thu, 6 Jun 2013 12:30:54 -0500
From: velocityxl at fastmail.fm
To: reflector at tvbf.org
Subject: Re: REFLECTOR: Prop dia
Sure sorry Engine RPM 4200 prop 2500 RPM
On 6/6/2013 11:23 AM, steve korney
wrote:
Ron...
It would be helpful to tell us what rpm the prop is turning
along with the engine rpm...
Steve
> Date: Thu, 6 Jun 2013 11:14:25 -0500
> From: velocityxl at fastmail.fm
> To: reflector at tvbf.org
> Subject: Re: REFLECTOR: Prop dia
>
> Motor is good . I have been using my fixed pitch through
the phase one
> and it works very well.
> I am turning my engine 5500 rpm to get a top speed of 180
knots So I
> got the IVo propeller on ebay and want to give it a try.
It is a little
> long 76 diameter so I was thinking
> of cutting it down. I will fly with it first to see what
it is like
> before I cut it down. Right now I like to cruise at 145
knots turning
> 4200 rpm. My comfort rpm . My goal is to
> run the engine at 4200 and cruise 160 knots with the hope
of not too
> much loss in take off performance.
>
> Ron
>
>
> On 6/6/2013 10:49 AM, John Dibble wrote:
> > I previously flew with 1" shorter blades (66" pitch)
for more
> > clearance. I couldn't quite use full power and stay
below 2600 rpm.
> > So I went back to the 68" pitch recommended by IVO.
Now I can easily
> > get down to 2500 rpm at full power. I think it would
go lower, but
> > haven't checked. 1" change in blade length makes a
big difference.
> > IVO shortened blades for me once. Seems like your
72" blades should
> > work. Have you checked that the motor is working
good?
> >
> > John
> >
> > On 6/6/2013 10:30 AM, Ron N VelocityXLFG wrote:
> >> Lower RPM at higher speed. I have a email out to
Ivo to see about
> >> making the blades shorter . Have not heard back
yet.
> >> From past experience they are a little slow in
response.
> >>
> >>
> >> Ron
> >> On 6/6/2013 8:10 AM, John Dibble wrote:
> >>> On 6/5/2013 4:13 PM, Ron N VelocityXLFG
wrote:
> >>>> I have a 72 dia prop on my XLFG I am
going to try a 76 inch Dia
> >>>> Ivo propeller and I am a little
concerned with the clearance . Seems
> >>>> like I have plenty even with a high
rotation angle. Is there any
> >>>> other concerns or advice out there for
this configuration.
> >>>>
> >>>> Ron
> >>>>
_______________________________________________
> >>>> To change your email address, visit
> >>>>
http://www.tvbf.org/mailman/listinfo/reflector
> >>>>
> >>>> Visit the gallery! www.tvbf.org/gallery
> >>>> user:pw = tvbf:jamaicangoose
> >>>> Check new archives:
www.tvbf.org/pipermail
> >>>> Check old archives:
> >>>>
http://www.tvbf.org/archives/velocity/maillist.html
> >>>>
> >>> If you do have ground contact, the blades
are easily repairable or
> >>> you can cut a little off the ends. My 220 HP
Franklin uses a 68"
> >>> IVO prop. 76" seems like a lot. What is the
objective?
> >>>
> >>> John
> >>>
_______________________________________________
> >>> To change your email address, visit
> >>>
http://www.tvbf.org/mailman/listinfo/reflector
> >>>
> >>> Visit the gallery! www.tvbf.org/gallery
> >>> user:pw = tvbf:jamaicangoose
> >>> Check new archives: www.tvbf.org/pipermail
> >>> Check old archives:
http://www.tvbf.org/archives/velocity/maillist.html
> >>
> >> _______________________________________________
> >> To change your email address, visit
> >> http://www.tvbf.org/mailman/listinfo/reflector
> >>
> >> Visit the gallery! www.tvbf.org/gallery
> >> user:pw = tvbf:jamaicangoose
> >> Check new archives: www.tvbf.org/pipermail
> >> Check old archives:
http://www.tvbf.org/archives/velocity/maillist.html
> >>
> >
> > _______________________________________________
> > To change your email address, visit
> > http://www.tvbf.org/mailman/listinfo/reflector
> >
> > Visit the gallery! www.tvbf.org/gallery
> > user:pw = tvbf:jamaicangoose
> > Check new archives: www.tvbf.org/pipermail
> > Check old archives:
http://www.tvbf.org/archives/velocity/maillist.html
>
> _______________________________________________
> To change your email address, visit
http://www.tvbf.org/mailman/listinfo/reflector
>
> Visit the gallery! www.tvbf.org/gallery
> user:pw = tvbf:jamaicangoose
> Check new archives: www.tvbf.org/pipermail
> Check old archives:
http://www.tvbf.org/archives/velocity/maillist.html
_______________________________________________
To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector
Visit the gallery! www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
_______________________________________________
To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector
Visit the gallery! www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.tvbf.org/mailman/private/reflector/attachments/20130606/7754146b/attachment-0001.html>
More information about the Reflector
mailing list