REFLECTOR: Reflector Digest, Vol 77, Issue 41 - Door open sensors

Alex Balic velocity_pilot at verizon.net
Sun Aug 7 13:09:10 CDT 2011


I used short lengths of carbon fiber arrow shaft for the plungers, but same
location- on the frame, not the door..

-----Original Message-----
From: reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org] On
Behalf Of Mark Riley
Sent: Sunday, August 07, 2011 9:06 AM
To: reflector at tvbf.org
Subject: Re: REFLECTOR: Reflector Digest, Vol 77, Issue 41 - Door open
sensors

Geoff:

You should absolutely have door open sensors and make a check of the light
and feeling each door handle your final pre-takeoff check.  The microswitch
for the door sensor is typically mounted below one of the receiving tubes in
a lower door latch. You then use a spacer made from a section of venetian
blind rod (really) to have the pin push down to activate the microswitch
when the door is latched. I have a door open annunciator light right at the
top of my panel. 

Since the microswitches are at the bottom of the door and run through the
duct, there is no wire flexing. I have detailed pictures of the install on
my blog. If you need more info, just email me.

Mark
On Aug 7, 2011, at 9:46 AM, reflector-request at tvbf.org wrote:

> Send Reflector mailing list submissions to
> 	reflector at tvbf.org
> 
> To subscribe or unsubscribe via the World Wide Web, visit
> 	http://www.tvbf.org/mailman/listinfo/reflector
> or, via email, send a message with subject or body 'help' to
> 	reflector-request at tvbf.org
> 
> You can reach the person managing the list at
> 	reflector-owner at tvbf.org
> 
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of Reflector digest..."
> 
> 
> Today's Topics:
> 
>   1. Re:  Nose Gear Microswitch (Michael Watson)
>   2. Re:  Nose Gear Microswitch (aminetech at bluefrog.com)
>   3.  Door lock microswitch wiring (Geoff Gerhardt)
> 
> 
> ----------------------------------------------------------------------
> 
> Message: 1
> Date: Sat, 6 Aug 2011 20:47:52 -0400
> From: Michael Watson <mikewatsspg at gmail.com>
> Subject: Re: REFLECTOR: Nose Gear Microswitch
> To: Velocity Aircraft Owners and Builders list <reflector at tvbf.org>
> Message-ID:
> 	<CAPgogjOFRHied_f5KSCvfpBiz3uwoi7Z+biWCkPgEAsn_6oObQ at mail.gmail.com>
> Content-Type: text/plain; charset="iso-8859-1"
> 
> Hi John,
> 
> The switch is closed when the light is on. 12 volts is supplied to the
> switch through the lamp, closing the switch (gear down and locked)
completes
> the
> circuit to ground turning on the lamp.  The test button acts as a ground
for
> all 3 lamps. Since that works, I'd say you have bad (intermittent) grounds
> to
> the switch connections.
> 
> BTW: Don't you carry a 12" metal rod to slide through the keel under the
> nose wheel shocks. It prevents a collapse if the over center is not
locked,
> or the
> Tower tells you that the gear is down but the light is off.
> 
> Good Luck,
> 
> On Sat, Aug 6, 2011 at 12:51 PM, <aminetech at bluefrog.com> wrote:
> 
>> After lowering my gear for landing a few days ago, the nose gear
indicator
>> light did not come on.  I asked the tower to check and he said the gear
was
>> down, but he had no way to tell if it was all the way down.  I retracted
and
>> went around.  The sun was on the panel during final.  Downwind I lowered
the
>> gear and with the sun gone I could see that the nose light was dimly lit,
so
>> I decided to take a chance.  On short final the gear warning light came
on
>> (not the nose light, but a separate light that comes on if either the
nose
>> or mains are not down), so I held my breath and was relieved when all was
>> OK.  I had recently adjusted the nose gear and switch.  I did it with the
>> normal weight on the nose gear.  I thought that maybe the overcenter
linkage
>> might move down a bit with no weight, so I checked and that was the case.
>> So I adjusted the switch to compensate for this.  When I checked the
lights,
>> the nose gear light was on, but 2 main gear lights were out.  I pressed
the
>> test button and all 3 came on.  When I released it, they all stayed on.
So
>> I replaced the keel cover and checked the lights again.  This time the
nose
>> gear light was out.  It came on with the test button, but went back out
when
>> I released it.  I'm going to check the microswitch, although I think it's
>> OK.  Is the switch circuit open or closed when the green light is on?
Any
>> ideas of what else to check?
>> 
>> Thanks,
>> 
>> John
>> 
>> _______________________________________________
>> To change your email address, visit
>> http://www.tvbf.org/mailman/listinfo/reflector
>> 
>> Visit the gallery!  www.tvbf.org/gallery
>> user:pw = tvbf:jamaicangoose
>> Check new archives: www.tvbf.org/pipermail
>> Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
>> 
> 
> 
> 
> -- 
> Mike W.
> 1997 Velocity Elite RG
> Franklin /IVO Electric CS
> Dual GRT EFIS HX Synthetic Vision
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL:
<http://www.tvbf.org/mailman/private/reflector/attachments/20110806/637bbdd0
/attachment-0001.htm>
> 
> ------------------------------
> 
> Message: 2
> Date: Sat, 6 Aug 2011 19:06:14 -0700
> From: <aminetech at bluefrog.com>
> Subject: Re: REFLECTOR: Nose Gear Microswitch
> To: "Velocity Aircraft Owners and Builders list" <reflector at tvbf.org>
> Message-ID: <20110806190614.96E9F49F at resin06.mta.everyone.net>
> Content-Type: text/plain; charset="us-ascii"
> 
> An HTML attachment was scrubbed...
> URL:
<http://www.tvbf.org/mailman/private/reflector/attachments/20110806/c957ee3f
/attachment-0001.htm>
> 
> ------------------------------
> 
> Message: 3
> Date: Sun, 7 Aug 2011 09:37:51 -0400
> From: Geoff Gerhardt <geoff.gerhardt at gmail.com>
> Subject: REFLECTOR: Door lock microswitch wiring
> To: Velocity Aircraft Owners and Builders list <reflector at tvbf.org>
> Message-ID:
> 	<CAHd2h4LPXsZ_pLT3Q6XdC-7scxq=MwhFa6q2G6Guh9a1dPoXDw at mail.gmail.com>
> Content-Type: text/plain; charset="iso-8859-1"
> 
> Folks,
> 
> I want to put microswitches in the door to detect the lock plunger
> position.  I will wire this into my annunciator panel which has an audible
> alarm.  But, I'm wondering if anyone else has wired their door open
sensors
> inside the door as I'm interested in seeing how you ran the wires.  I'm
> concerned about fatigue of the wires having to flex every time the door
> opens/closes.  At Oshkosh, I saw that Lancairs have some nice plunger-type
> connectors on their doors (see attached).  I found the manufacturer for
> these and was considering using one.
> 
> I remember a year or so ago, after that tragic crash due to a door open,
> there was discussion about this.  Anyone else putting door-open sensors in
> the doors?
> 
> Thanks.
> 
> Geoff
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL:
<http://www.tvbf.org/mailman/private/reflector/attachments/20110807/12fa62ec
/attachment.htm>
> -------------- next part --------------
> A non-text attachment was scrubbed...
> Name: P7283945 (Medium).JPG
> Type: image/jpeg
> Size: 97313 bytes
> Desc: not available
> URL:
<http://www.tvbf.org/mailman/private/reflector/attachments/20110807/12fa62ec
/attachment.jpeg>
> 
> ------------------------------
> 
> _______________________________________________
> Visit the gallery!  tvbf:jamaicangoose
> 
> End of Reflector Digest, Vol 77, Issue 41
> *****************************************

_______________________________________________
To change your email address, visit
http://www.tvbf.org/mailman/listinfo/reflector

Visit the gallery!  www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html




More information about the Reflector mailing list