REFLECTOR: Canard Center Hinge
Richard J. Gentil
richard at naples-air-center.com
Thu Apr 14 00:43:28 CDT 2011
Jeff,
Not at all. It was more like removing 15 years of rust along with such a small amount from the inner diameter that you could only tell with micrometer.
Richard
Sent from my iPhone 4
On Apr 13, 2011, at 6:54 PM, "jcbarnes411 at sbcglobal.net" <jcbarnes411 at sbcglobal.net> wrote:
> Hi Richard, didn't you just WEAKEN the torque tube?
>
> Regards, Jeff Barnes
>
> Sent from my HTC on the Now Network from Sprint!
>
> ----- Reply message -----
> From: "Richard J. Gentil" <richard at naples-air-center.com>
> Date: Wed, Apr 13, 2011 2:27 pm
> Subject: REFLECTOR: Canard Center Hinge
> To: "Velocity Aircraft Owners and Builders list" <reflector at tvbf.org>
>
> Don,
>
> Those were the bearings I ordered last month. Their outer diameter turned it to be a fraction larger then the inner diameter of the torque tubes. I solved the issue be taking a piece of a wooden broom handle, mounting it on the end of a drill, wrapping the broom handle with sandpaper and reaming out the inner diameter of the torque tubes.
>
> I used normal washers as spacers and two large area washers against the center hinge to make sure the bolt could not pivot from side to side.
>
>
>
> Richard
>
> Sent from my iPhone 4
>
> On Apr 13, 2011, at 2:31 PM, Don Johnston <don at numa.aero> wrote:
>
> > I almost always end up on the "aviation grade" part side of the fence...
> >
> > The McMaster-Carr bearings are a very high quality bearing and they only cost $7.10 each. I don't have an Aircraft-Spruce version but I wouldn't be a bit surprised is they were identical.
> >
> > http://www.mcmaster.com/#6384k55/=buzun1
> >
> > The other thing I did was to use a large area washer on either side of each bearing that's a little smaller than the OD of the bearing.
> >
> > -Don
> >
> > Don Johnston
> > www.velocity-xl.com
> >
> > Date: Wed, 13 Apr 2011 07:48:04 -0500
> > From: " Brett Ferrell " <reflector at velocityxl.com>
> > Subject: Re: REFLECTOR: Canard Center Hinge
> > To: reflector <reflector at tvbf.org>
> >
> > There is now a [LINK:
> > http://www.velocityxl.com/wiki/index.php?title=Elevator_Center_Bearing]
> > Wiki page describing this modification, with a complete parts list with
> > links to the Aircraft Spruce parts page. The mod can be purchased for
> > under $50 currently. Thanks to [LINK:
> > http://www.velocityxl.com/album.php?albumid=24] Bill Mulrooney for the
> > design and [LINK: http://kal-soft.com/velocity/] Andy Millin for the
> > pictures.
> >
> > Brett
> > N44VF
> >
> >
> >
> > http://www.mcmaster.com/#6384k55/=buzun1
> > _______________________________________________
> > To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector
> >
> > Visit the gallery! www.tvbf.org/gallery
> > user:pw = tvbf:jamaicangoose
> > Check new archives: www.tvbf.org/pipermail
> > Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.tvbf.org/mailman/private/reflector/attachments/20110414/9abfe0d4/attachment.htm>
More information about the Reflector
mailing list