REFLECTOR: TR: TR: Autopilot servos

Gilles Ross rossgil at globetrotter.net
Wed Mar 26 17:23:55 CDT 2008






Thanks
Very interesting comments and pictures!
What is the purpose of the enclosing around the roll servo ?
Gilles

-----Message d'origine-----
De : reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org]De la
part de Craig and Denise Woolston
Envoye : 26 mars 2008 06:47
A : 'Velocity Aircraft Owners and Builders list'
Objet : Re: REFLECTOR: TR: Autopilot servos


We mounted our BM servos in a very similar location and are flying.  I would
strongly recommend moving the aileron servo to the engine compartment.  We
have not had very good luck get our roll control to be smooth and positive.
After complaining to BM they say we should have mounted the servo closer to
the actual surface, that the slop of the push-pull cables is affecting the
performance.  I've attached my pictures of install for reference.

Craig
XL5-FG Flying in Lancaster, CA




-----Original Message-----
From: reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org] On
Behalf Of Alex Balic
Sent: Monday, March 24, 2008 5:26 PM
To: 'Velocity Aircraft Owners and Builders list'
Subject: Re: REFLECTOR: TR: Autopilot servos

Hi Gilles-

I will try to get out there and take a picture or you, but basically, I
removed the output arm from the servo- then fabricated an adapter that would
allow a small universal joint to attach to the output shaft of the servo,
then I adapted the end of the universal joint to fit into the  torque tube
directly- I probably could have made a plug to go directly from the servo
into the tube, but I felt that there might be the possibility of binding, so
I added the U-joint- the servo mounts on the floor behind of the keel on an
aluminum hat channel piece that I fabricated. The only disadvantage that I
see is that the servo has no mechanical advantage on the aileron system- if
you use an output arm, and a rod linkage to the end of the aileron arm that
pushes/pulls the flex cables, you can set it up with maybe 1.5 to one
advantage- I hear that the servo is plenty strong to move the ailerons
though, but the other advantage of using the mechanical  linkage is that the
servo would not have to be as precise- maybe 3 degrees servo travel to 2
degrees aileron arm travel- I have not flown with it yet, but the install is
clean.

Alex

-----Original Message-----
From: reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org] On
Behalf Of Gilles Ross
Sent: Monday, March 24, 2008 10:58 AM
To: reflector at tvbf.org
Subject: REFLECTOR: TR: Autopilot servos


Thanks Alex
Do you know the arm lenght of your attachment in reference with the center
on the torque tube
and which hole (or arm lenght) did you used on the servo arm.
Gilles

-----Message d'origine-----
De : reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org]De la
part de Alex Balic
Envoye : 24 mars 2008 10:44
A : 'Velocity Aircraft Owners and Builders list'
Objet : Re: REFLECTOR: Autopilot servos


I put my elevator servo on top of the canard- I bought another trim spring
bracket from Velocity and attached it on the other elevator torque tube-
connected to that- I mounted my roll servo at the end of the keel co Axially
with the aileron torque tube- it is connected to the torque tube with a
small universal joint.

-----Original Message-----
From: reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org] On
Behalf Of Gilles Ross
Sent: Sunday, March 23, 2008 8:54 PM
To: reflector at tvbf.org
Subject: REFLECTOR: Autopilot servos

I am looking where BMA autopilot servos have been installed for the elevator
and aileron.

Has anyone installed the elevator servo in the keel?

Gilles

_______________________________________________
To change your email address, visit
http://www.tvbf.org/mailman/listinfo/reflector

Visit the gallery!  www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html


_______________________________________________
-------------- next part --------------
A non-text attachment was scrubbed...
Name: pitch_servo.JPG
Type: image/jpeg
Size: 26727 bytes
Desc: not available
Url : http://www.tvbf.org/mailman/private/reflector/attachments/20080326/9ee67f93/attachment-0002.jpeg 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: roll_servo.JPG
Type: image/jpeg
Size: 45998 bytes
Desc: not available
Url : http://www.tvbf.org/mailman/private/reflector/attachments/20080326/9ee67f93/attachment-0003.jpeg 
-------------- next part --------------
_______________________________________________
To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector

Visit the gallery!  www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html


More information about the Reflector mailing list