REFLECTOR: door strake cut lines

[gpoole]

Hi Jorge,

Think you meant to say that you started at 900 as per manual for the
door/strake cut and came back to 800 (not 1000) to give better access...if I
read your web page right...

Best,

Greg in Sydney




-----Original Message-----
From: reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org] On
Behalf Of Jorge Bujanda
Sent: Tuesday, 4 September 2007 9:14 AM
To: 'Velocity Aircraft Owners and Builders list'
Subject: Re: REFLECTOR: door strake cut lines

Thanks.  Glad to be of help if I can.

Regards,
Jorge


-----Original Message-----
From: reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org] On
Behalf Of Andrew
Ellzey
Sent: Monday, September 03, 2007 8:04 AM
To: Velocity Aircraft Owners and Builders list
Subject: Re: REFLECTOR: door strake cut lines

Thanks Jorge for your reply. I spent quite a bit of time looking at your web
site and your
construction pictures and I would like to commend you for your good work and
attention to
detail. As the saying goes a picture is worth a thousand words.
 
Andy

----- Original Message ----
From: Jorge Bujanda <bujanda at dslextreme.com>
To: Velocity Aircraft Owners and Builders list <reflector at tvbf.org>
Sent: Monday, September 3, 2007 8:56:22 AM
Subject: Re: REFLECTOR: door strake cut lines


Hi Andy,
I initially started cutting the bottom right strake shell at 90° (manual)
but felt the
strake was somewhat interfering unnecessarily with the access to the cabin.
I then cut it
at I believe 100 degrees.  Click on the link below and check out photo 2 in
#6 (Strake
Door Cut) of the Right Strake section. 
http://members.dslextreme.com/users/jbujanda/Construction.html#Fuel
You could go higher at the expense of the storage compartment, if you want. 

Regards,
Jorge Bujanda
Velocity XL FG 
Palmdale, CA
Website:  http://members.dslextreme.com/users/jbujanda/

"Make your best case... not the best case."
"Spare the noise... convince through silence."


-----Original Message-----
From: reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org] On
Behalf Of Andrew
Ellzey
Sent: Sunday, September 02, 2007 7:19 PM
To: Velocity Aircraft Owners and Builders list
Subject: REFLECTOR: door strake cut lines

I completed, what has been for me, a long road last weekend. I closed both
strakes. I
still have all the additional lay-ups that now need to take place when you
put your strake
tops on, but now I think I would like to cut the strake noses off and attach
them to my
doors. My question is at what angle has everyone cut the strake to door nose
piece off?
The manual calls for 90 degree from the fuselage. I seem to remember that
most people were
using 98 to 95 degrees from the fuselage to have better clearance when the
door starts to
open. Please provide feedback.

Andy Ellzey

_______________________________________________
To change your email address, visit
http://www.tvbf.org/mailman/listinfo/reflector

Visit the gallery!  www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html


_______________________________________________
To change your email address, visit
http://www.tvbf.org/mailman/listinfo/reflector

Visit the gallery!  www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html

_______________________________________________
To change your email address, visit
http://www.tvbf.org/mailman/listinfo/reflector

Visit the gallery!  www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html


_______________________________________________
To change your email address, visit
http://www.tvbf.org/mailman/listinfo/reflector

Visit the gallery!  www.tvbf.org/gallery
user:pw = tvbf:jamaicangoose
Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
-------------- next part --------------
A non-text attachment was scrubbed...
Name: winmail.dat
Type: application/ms-tnef
Size: 6064 bytes
Desc: not available
Url : http://www.tvbf.org/mailman/private/reflector/attachments/20070904/48c875dc/attachment-0001.bin