REFLECTOR: 24 volt electrical system

[Joe Ewen]

The duty cycle for the 30 amp load is very low.  If one is practicing takeoffs and landings, there are maybe 8 - 15 second cycles.  If the load imbalance is an issue the circuit could be accomplished by using schottky diodes and paralleling the load off both batteries.  See attached.  A converter for that size load is likely to be rather expensive and bulky.

Joe
  ----- Original Message ----- 
  From: Jim 
  To: Velocity Aircraft Owners and Builders list 
  Sent: Wednesday, September 27, 2006 7:26 PM
  Subject: Re: REFLECTOR: 24 volt electrical system


  jewen at comporium.net wrote: 
Andy,

Use 2 12 volt batteries in series (24v.)  For the 12 volt circuit(s),
center tap between the two batteries. See attached drawing.

Joe




On Wed, September 27, 2006 10:27 am, Andrew Ellzey wrote:
  I would have liked to use a 24 volt electrical system on my aircraft, the
problem is the hydraulic gear pump system being 12 volt @ 30 amp. Has
anyone flying an XLRG found a way around this issue?

Andy Ellzey_______________________________________________
To change your email address, visit
http://www.tvbf.org/mailman/listinfo/reflector


Visit the gallery!  www.tvbf.org/gallery
user:pw Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
    
  ----------------------------------------------------------------------------
_______________________________________________
To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector

Visit the gallery!  www.tvbf.org/gallery
user:pw Check new archives: www.tvbf.org/pipermail
Check old archives: http://www.tvbf.org/archives/velocity/maillist.htmlJoe

  It is not a good idea to use the circuit and set up the batteries as you have indicated you are better off to use a converter to lower the voltage.  By following the circuit as discribed  you will over charge the battery located at the location 12 V to 24 Volts, what happens is the altenator or generator supplies a current  (Amps) to operate the equipment installed in the aircraft or other device.  Both batteries receive say 50 amps or so the battery located at 0 to 12 Volts receives 50 anps - the current required to operate the equipment associated with it let's say 30 amps for the equipment so 20 amps is charge for the 0 - 12 Volt battery.  The battery located at the 12V -24 Volt location also receives 50 Amps but only 5 amps is required to maintain / operate the equipment in its circuit.  The battery located at 12 Volts to 24 Volts will receive an extra 45 amps and will boil or dry out in short order and there will be very low capacity in this battery and you will be repl;acing it on a regular basis and not understand why it is failing as it has no load and it should not be the one that is failing.  

  Regards
  Jim Greening



------------------------------------------------------------------------------


  _______________________________________________
  To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector

  Visit the gallery!  www.tvbf.org/gallery
  user:pw   Check new archives: www.tvbf.org/pipermail
  Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.tvbf.org/mailman/private/reflector/attachments/20060927/06933722/attachment.html 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: 24-12 Volt Battery System 2.pdf
Type: application/pdf
Size: 10228 bytes
Desc: not available
Url : http://www.tvbf.org/mailman/private/reflector/attachments/20060927/06933722/attachment.pdf