REFLECTOR: Rudder conduits on Alan Shaw wings
Brian Michalk
michalk at awpi.com
Sun Aug 27 18:45:31 CDT 2006
Can you get a stiff wire in there, like piano wire?
Find a friend with some telco equipment, or a networking guy. They may
have a cable finder.
Run the piano wire in as far as it goes. Attach the transmitter, then
find the other end of the wire with the receiver.
lawrence epstein wrote:
> Try again with picture
>
>> From: "lawrence epstein" <ljepstein at hotmail.com>
>> Reply-To: Velocity Aircraft Owners and Builders list <reflector at tvbf.org>
>> To: reflector at tvbf.org
>> Subject: REFLECTOR: Rudder conduits on Alan Shaw wings
>> Date: Sun, 27 Aug 2006 20:39:02 +0000
>>
>> I asked for suggestions about this some months ago and have tried them
>> all. Still no joy.
>>
>> The folowng is an e-mail I sent to Alan. Anybody have any other
>> suggestions?
>>
>> Alan-
>> I hope all is well. I continue to follow Wingco/Atlantica and look
>> forward to it's success.
>>
>> Anyway-
>>
>> I have been trying to find the rudder conduits on my (WingCo/V173)
>> wings and can't!
>>
>> There was a lot of spillage in the recess where the internal arm
>> should go and the conduit (Outboard) end should be as well as some
>> "displaced" triax.
>> I spoke to a few people who had your wings and had similar problem
>> finding the condit end and all said just keep digging and cutting. I
>> confirmed with the factory that even triax cut away 5-6" in the well
>> would still not be a structural problem.
>>
>> Anyway, digging was a problem from the opening. I then saw a velocity
>> at Oshkosh that had your wings and had the same problem. He had cut an
>> access panel about 3" diameter centered 5" fwd of the opened edge (he
>> covered it wth plexiglass to have easy inpection of the rudder
>> cable/turnbuckle). THis looked like a good solution and I again
>> discussed it with Duane Swing and Ken Baker @ the Velocity tent and
>> all were OK with the structure.
>>
>> Well I cut the holes and dug away, completely exposing the outboard
>> end of the blue foam of the wing from about 3 to 7 inches fwd of the
>> winglet open edge, top to bottom and NO CONDUIT!!!
>>
>> Where should I look now? Any suggestions? I have tried to get a stiff
>> wire thru the conduit from inboard to outboard but anything
>> heavy/stiff enough to chuck in a drill, won't pass more than about 3
>> feet and and the smaller stuff goes only about 5-6 feet.
>>
>> I have attached a photo
>>
>
>
>> << 100_1000.jpg >>
>
>
>
>> _______________________________________________
>> To change your email address, visit
>> http://www.tvbf.org/mailman/listinfo/reflector
>>
>> Visit the gallery! www.tvbf.org/gallery
>> user:pw = tvbf:jamaicangoose
>> Check new archives: www.tvbf.org/pipermail
>> Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
>
>
>
> ------------------------------------------------------------------------
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> To change your email address, visit http://www.tvbf.org/mailman/listinfo/reflector
>
> Visit the gallery! www.tvbf.org/gallery
> user:pw = tvbf:jamaicangoose
> Check new archives: www.tvbf.org/pipermail
> Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
More information about the Reflector
mailing list