REFLECTOR: Major Outline

[Chuck Jensen]

Terry,
 
I'll take a cut at one of them.  I had the spider on top of the engine.  The lines were insulated but in the summer, it was still rough running after a flight unless I ran the fuel pump.  When I did some engine work, I had all the fuel line insulation removed, I found that in the summer, it was rough running after a flight unless I ran the fuel pump.  More of the story, lessons learned, et al--spider on top is just fine (easy to get at, assuming your make a hatch and cut access holes in the pressure baffle.  Running the pump on the ground to get smooth operations is no big deal.  Winter time, its a never mind.  I have a Rose EI and mag.
 
Chuck, IO-540
 
 
-----Original Message-----
From: reflector-bounces at tvbf.org [mailto:reflector-bounces at tvbf.org]On Behalf Of Terrence Miles
Sent: Friday, April 29, 2005 8:26 AM
To: 'Velocity Aircraft Owners and Builders list'
Subject: RE: REFLECTOR: Major Outline


Hey ya'll,
 
I know this is not directly to the topic CHT issues at hand, but I have an engine cooling problem to toss on the table.  I am trying to refine an engine order for an IO540k w/ Lasar ign turning an aerocomposite CS 3 blade prop.  I'll have the top cut naca scoops in this XL and not the armpit cooling.  Here's my question:  Is there a best place to locate the spider valve (SV) (fuel distrib)?  Concern would be trying to restart a hot engine on the ramp.  My concern is vapor lock.  If I put the SV on top of the engine it's hot up there, but the naca can then work backwards.  I have seen heat air ripples coming off of them just after shutdown.    If I locate it on the bottom face of the engine there is less hot air rising but maybe lesser ventilation?  Anybody have any experience with this?  I am favoring the top mount.
 
New 2nd question which is related:  I am trying to give D. George a final buildup profile.  Here my take on ignition.  The emag/pmag folks only make a 4 cyl version of their stuff.  Jeff Rose is selling the biz, so I counted him out.  That left light speed and Lasar it seems to me.  The lasars will revert to basic self generation for spark on loss of electrical.  The lightspeeds do not.  I am choosing Lasar.  Whadaya think?  In fact I already have a lasar timing box I got 2nd hand.  
 
New 3rd Question:
Likely I will do the Nuckols Z-14:  
Dual batts.  I weigh 150 lbs and will fly solo a lot, so the dual batts are as much a CG fixer.  
Dual alts:  Less sure on this need.  But if done, 20amps vs 8amps on the pad and 60 amps or so belt-driven
Bus structure:  Work in progress.  
Panel:  GRT with one AHRS and 3 screens.  Back up attitude w/ TruTrak.  Back up ias/altitude w/ GRT EIS which will be panel mounted.  
 
And now for a bit of humor from the new guy on the block...I hope to be in the air by Christmas.  Thank you all very very much for the warm welcome and the brain drain I will be (have already been) for these 1st months.  Anybody drifting through Greenville, SC, the front light is always on, and I just bought a new coffee pot.  
 
Thanks,
Terry
XL RG-5
Wings ready to glass tomorrow
Bulkheads going in today
Hangar 18
 
Check old archives: http://www.tvbf.org/archives/velocity/maillist.html
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.tvbf.org/mailman/private/reflector/attachments/20050429/ac071061/attachment.html